Kenton VP-330 (after Jan 06) Bedienungsanleitung PDF herunterladen

User instructions for Kenton MIDI retrofit for

ROLAND VOCODER Mk1 & Mk2

These instructions are only for Vocoder MIDI retrofit kits produced after 1

January 2006

Firmware versions RVOC5100 or later

N.B. Different instructions apply to earlier Kenton Vocoder MIDI retrofit kits.

USING THE MIDI INTERFACE

When you turn on the synthesizer for the first time, you will be in omni-off mode channel 1 for receive - See the

following pages for other factory default settings. When you select a receive channel, this will be stored in memory

and will be remembered for when you subsequently turn on the synth - all parameters listed on the next page are

stored.

If you want to put the machine back to the factory default settings at any time, switch the synth on whilst holding the

red push button pressed - hold for a couple of seconds then release.

RED PUSH BUTTON

Two modes are available by pushing the red push button during normal playing mode. Before you press the red

button however, make sure that no keys are pressed on the remote MIDI keyboard otherwise the results may be

unpredictable. The key presses detailed below must be entered on the remote MIDI keyboard only

1) SET-UP MODE

For setting MIDI channels and assignments. Give the red push button two short presses (half a second each) - then

release. Follow this with a key or sequence of keys as detailed on page 2. After making a MIDI channel assignment,

you will be automatically returned to playing mode but after making other assignments you will need to press the

ENTER key (Top C) to return to playing mode. This is to enable you to make the multiple key presses required

when re-assigning Sources to Destinations. (N.B. all set-ups are stored in non volatile memory).

2) TRANSPOSE MODE Press and hold the red push button for about four seconds - then release. Middle C will

sound on the synth and continue to sound until you press a key. The key that you press on the remote keyboard will

be the new middle C for MIDI IN. You can set any value up to two octaves up or down - settings outside this range

will be ignored (where middle C = no transposition) . Note that transpose mode cannot be entered from set-up

mode. (N.B. the transposition will be stored in non volatile memory).

The bottom four octaves on a 61 note remote keyboard are used to set "transpose" - with middle C being the

transpose OFF point.

1 2 3 4

Inhaltsverzeichnis

Seite 1 - ROLAND VOCODER Mk1 & Mk2

User instructions for Kenton MIDI retrofit for ROLAND VOCODER Mk1 & Mk2 These instructions are only for Vocoder MIDI retrofit kits produced

Seite 2

Function of keys during set-up mode: C Receive channel 1 (default) [ Bottom C - MIDI note #36 ] Db " " 2 D "

Seite 3 - ADDITIONAL INFORMATION

ADDITIONAL INFORMATION 1) Receive channel setting will return you directly to playing mode, all other keys will let you stay in SET-UP mode until y

Seite 4

GENERAL INFORMATION ABOUT MIDI CONNECTIONS Any MIDI IN should be connected to a MIDI OUT or a MIDI THRU similarly any MIDI OUT should be connected o

Verwandte Modelle: VP-330

Kommentare zu diesen Handbüchern

Keine Kommentare

Kenton VP-330 (after Jan 06) Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Ausrüstung Kenton VP-330 (after Jan 06) herunter. Kenton VP-330 (after Jan 06) User Manual [cs] [pl] [en] [de] Benutzerhandbuch

Inhaltsverzeichnis

Verwandte Modelle: VP-330

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Ausrüstung Kenton VP-330 (after Jan 06)